Applications - EPICS Driver Control

BOP 1KW EL, GL Series High Power Power Supply

• Source & sink, 4 quadrant operation.
• Fast analog programming.
• Optimized for very low ripple, noise and temperature stability in current mode.
• Precision stabilization: 0.001% source, 0.002% load.
• Digital programming: All models include RS 232, GL suffix includes GPIB, EL suffix includes LAN (ethernet)
• Built-in arbitrary waveform generator.
• EPICS Driver (Linux compatible) now available!

BOP 1KW MG, ME HIGH POWER SERIES
d-c bipolar power, 1KW

• Source & sink, 4 quadrant operation.
• Fast analog programming.
• Precision stabilization: 0.001% source, 0.002% load.
• Digital programming: All models include RS 232, MG suffix includes GPIB, ME suffix includes LAN (ethernet)
• Built-in arbitrary waveform generator.
• EPICS Driver (Linux compatible) now available!

BOP-E Series Bipolar Ethernet-controlled power supplies

The BOP-E Series allows ethernet control of 100W, 200W and 400W BOP bipolar power supplies via LAN/Web pages.

• 14 Standard Models:
      • ± 0-5 Volts to ± 0-200 Volts,
      • ± 0-5 Amps to ± 0-20 Amps.
• True 4-quadrant programmable voltage and current power supplies.
• Dual-range 16-bit interface provides 15 bits of resolution for both full and quarter scale output.
• Setup using a web page.
• Power supply control via web pages and socket interfaces.
• Labview and C drivers provided
• Optional optimization to work with inductive loads or capacitive loads.
• 

Rectangular voltage/current operating boundaries, 2400 Watts, LAN control replaces standard RS 232 interface.

• GPIB & isolated analog controls standard on all models.
• VXI plug&play, LabView and IVI-COM drivers.
• Control via web browser using LAN interface.
• True 1U height - full power operation with no spacing between units.
• 200-240V a-c input with active PFC.
• Optional Rapid Output Discharge Circuit (RODC)
• EPICS Driver (Linux compatible) now available!

Option L (Inductive Load) for BOP (all models)

• Operate in Current or Current Limit Mode for loads up to 1 Henry.
• Also stable with any R-L series load combination.
• Optional digital displays.
• Optional BIT 4886 provides 16-bit IEEE 488.2 talk- listen control with SCPI support.
• Optional BIT 802E provides ethernet control either through a web page or by using SCPI commands via Telnet.
• Isolated analog control standard on all models.
  
• EPICS Driver now available (Linux compatible) with BIT 802E!

Low-profile, automatic crossover, high-performance, low-cost, stable programmable d-c power, 750, 1500, 3000 Watts, includes LAN interface

• 1U, Half Rack (750W)
• 1U, Full Rack (1500W)
  5KW, 10KW, 15KW 3U, Full Rack
  
• 2U, Full Rack (3000W)
• 3U, Full Rack (5KW, 10KW, 15KW)
• Analog and RS 485 programming of voltage, current and their limits
• Speed controlled fan for low acoustic noise
• 57 Models from 0-6V to 0-1500V up to 540A
• CE Mark
• EPICS Driver (Linux compatible) now available!

Voltage, current and power-limited operating boundaries, 1200 Watts, LAN control replaces standard RS 232 interface.

• GPIB & isolated analog controls standard on all models.
• VXI plug&play, LabView and IVI-COM drivers.
• Control via web browser using LAN interface.
• True 1U height - full power operation with no spacing between units.
• Wide range a-c input with active PFC.
• Optional Rapid Output Discharge Circuit (RODC)
• EPICS Driver (Linux compatible) now available!

DC Electronic Loads for testing power sources: batteries, power supplies, generators, chargers, fuel cells, etc.

• 1KW to 5KW Modules, 4U Height, Air Cooled
• Up to 600V d-c/Module
• Up to 800A d-c/Module
• Constant E, I, P, I/E, E/I
• Local, Remote Analog and Remote Digital Control
• USB and RS 232 Remote Control, GPIB and LAN optional
• EPICS Driver now available! with optional LAN interface
  

MST SERIES

• 200, 400W
• Programmable
• Switcher
• PFC
• Voltage/Current stabilizer
• IEEE 1118/GPIB Bus
• Input: 100-240V a-c/ 24/ 28/ 48V d-c
• 1 Output: 0 to 6/ 15/ 25/ 40/ 55/ 65/
                    75/ 100/ 150V d-c
• EPICS Driver (Linux compatible) now available!

High voltage (0-300V, 0-500V, 0-1000V, 0-2000V, linear, voltage-current stabilizers with rectangular (automatic crossover) output characteristic.

• Two sizes: half-rack 40 watts, full-rack 200 watts.
• FET output stage.
• Conventional filtering or fast response.
• Fast analog programming mode.
• Rapid recovery current mode in fast mode.
• Local control from panel-mounted keypad.
• Built-in GPIB, IEEE 488.2, 12 bits.
• Built-in RS 232 (except BHK 300-0.8MG; contact Kepco if this feature required)
• Support for SCPI language.
• 2-line 16 character LCD display.
• Full read back of voltage and current on the bus.
• Increased resolution and accuracy (x10) for reading small current.
• Versatile output on/off port (40 watt model).
• Extensive Protection circuitry
• EPICS Driver (Linux compatible) now available!

Linear low-noise power supplies respond very quickly and precisely to voltage and current setting instructions from either GPIB (IEEE 488.2) or front panel keypad.

• Linear control for low noise: 100 micro-volts typical in voltage mode
• High precision: 0.0005% source effect {regulation} in voltage mode.
• Voltage and current control with equivalent performance.
• A high speed mode allows fast-recovery current-controlled stabilization into a varying load.
• Overvoltage and overcurrent settings individually programmed by the front panel keypad or remotely by the bus with a programmable delay to allow for reactive-load transients.
• Overvoltage crowbar to protect sensitive loads.
• Non-volatile storage of programmed sequences or active settings.
• Full talk-listen control from a GPIB (IEEE 488-2) using SCPI language.
• Master-slave series and parallel operation to provide increased capability.
• Local control: Front panel keypad used to set and adjust output.
• EPICS Driver (Linux compatible) now available!

360, 720, 1080W (0-6V, 0-15V, 0-25V, 0-36V, 0-55V, 0-75V, 0-100V, 0-150V linear, voltage-current stabilizers with rectangular output characteristic.

• 360, 720, 1080W
• Programmable
• Voltage/Current stabilizer
• IEEE 1118 Bus
• Optional GPIB Adapter
• input: 115/230V a-c
• 1 Output: 0 to 6/ 15/ 25/ 36/ 55/ 75/ 100/ 150V
• EPICS Driver (Linux compatible) now available!

Bipolar d-c power, up to 500V or 1000V, 40 Watts.

• Linear 4-quadrant operation.
• FET output stage.
• Preamplifiers for summing and scaling arbitrary input signals.
• Wide bandwidth.
• Voltage and current stabilization with automatic crossover to current and voltage limits.
• Remote programming of voltage, current or both channels by external analog volage.

Linear voltage/current stabilizer, programmable via front panel keypad or IEEE 1118 Serial bus or optional GPIB or RS 232 interfaces.

• 360W
• Linear
• Programmable
• Voltage/Current stabilizer
• Keypad
• LCD
• IEEE 1118 (serial) bus
• GPIB and RS 232 optional
• Input: 115/230V a-c
• 1 Output: 0 to 6/ 15/ 25/ 36/ 55/ 75/ 100/ 150V d-c
• EPICS Driver (Linux compatible) now available!

• Digital Programmer
• 1 or 2 Channels
• IEEE 488 Listener for Kepco's Programmable Models (JQE , ATE,PAT, PTR etc.)
• Precise 0-10V analog output
• Kepco's SN 488 Digital Programmer facilitates digital programming via GPIB interface.
• EPICS Driver (Linux compatible) now available! Requires SN 488-121 (single channel) or SN 488-122 (dual channel) Programmer to convert digital hexadecimal (12-bit binary) data into a 0 - 10V precision analog voltage source.